1IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.OUTDOOR BUILT-IN GAS GRILLRobert H. Peterson Co. • 14724 East Proct
10ELECTRICAL CONNECTIONSThis grill requires 120VAC power to operate.Plug the power supply cord into a properly wired and inspected GFCI electrical rec
11INSTALLATION REQUIREMENTSInstallation must be performed by a qualifi ed professional service technician. This grill is designed for outdoor use only
12Fig. 12-1 - Ventilation diagramLeft-side hangerFig. 12-4Flex connectorLeft-side support wallOrient grill so prevailing wind blows this way.Fig. 12-3
13FOR YOUR SAFETY, you must provide the openings listed below for drainage, replacement air, and cross-ventilation of any storage area exposed to poss
14Fig. 14-3Adjustable support screwBottom of faceBottom of cut-out openingNote: When a propane cylinder is installed inside of the enclosure, the gu
15Fig. 15-1Zone dividerGrooveGrooveFrontINSTALLATION (cont.)INSTALL THE FLAVOR GRIDSPlace the fl avor grids directly onto the studs on the burners. The
16POWER SUPPLY HOOKUPCAUTION: IMPROPERLY CONNECTED WIRES WILL CAUSE DAMAGE TO THE GRILL AND MAY RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.This
17ULFig. 17-1 Type I Acme thread quick couplerPressure relief valveQCC Type 1 valveBrass Acme thread fi ttingLiquid level indicator (optional)Hand nut
18ULFig. 18-1 type coupleur rapide de fi l de point culminant d’IValvede décompressionQCC Type 1 ValveAjustage de précision en laiton de fi l de point c
19IDENTIFICATION OF GRILL CONTROLSFig. 19-1Leftmain burner control knobRightmain burner control knobDigital thermometerCenter main burnercontrol knobF
2IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATIONGRIL EXTÉRIEUR D’ÎLE DE GAZ D’ÉCHELONDANGER:SI VOUS
202. Use a Phillips screwdriver to remove the stainless-steel motor assembly housing screw. Pull the top of the housing fi rst up and then outward awa
21SHUTTING OFF THE UNITTo shut off the unit, depress each valve control knob and while pressing turn it clockwise to the OFF position.Always close th
22ARRÊT DU UNITÉPour couper le unité, diminuez chaque bouton de commande de valve et tout en pressant tour il dans le sens des aiguilles d’une montre
23DIGITAL THERMOMETER / INTERIOR AND KNOB LIGHTSYour grill comes with a digital thermometer for temperature monitoring and timed cooking. Pressing any
24DIGITAL THERMOMETER / INTERIOR AND KNOB LIGHTS (Cont.)Setting the Timer1. Press the timer button. Use the arrows to set the desired amount of time
25MENUSETOFFOFFON BACKLIGHTREDGREENBLUEFig. 25-1 Backlight screenUse arrows to select desired colorPress light button to turn ON/OFFSetting the Therm
26ROTISSERIE INSTRUCTIONSDrip tray linerFig. 26-3Backburner (unlit)Backburner coverWarming rackRotisserie rod rear bracketRotisserie rod and knobRotis
27The infrared (IR) searing burner (optional) cooks with a powerful radiant heat.Light the infrared burner following the LIGHTING INSTRUCTIONS in this
28The art of grilling involves learning the nuances of your grill and knowing how various cuts of meat and other foods cook on it under different sett
29THE DRIP TRAYThe drip collection system allows you to brush or scrape excess dried residue from the grilling area directly into the drip tray (see t
3CONTENTSREV 5 - 1412081445L-C2-3294 REPLACEMENT PARTS LIST7 COUNTERTOP OVERHANG7 MODEL SPECIFICATIONS8 SUBSTRATE8 BUILT-IN GRILL DIMENSIONS TABLE9
30Drippings from grilling flow through specially designed channels and collect in the drip tray . Check the drip tray regularly and empty when requir
31Fig. 31-1 - Wipe with grainPROTECTING YOUR APPLIANCE FROM THE WEATHERAn optional cover will protect your appliance when not in use. (Allow to cool b
32Your grill is engineered with the conveniences of electrical power for illuminating and igniting the grill. To replace any oven light, follow the in
33POWER SUPPLY FUSE REPLACEMENT1. Locate the power supply box inside of the island enclosure (reference the PARTS LIST).2. Using a phillips screwdri
34REGULATOR CONVERSIONThe gas regulator, located behind the control panel, must be set for the type of gas used to fuel the grill. To check the regula
35CONVERTING THE GAS TYPE3. Unfasten the two back burner nuts (found on the left side of the back burner) using a 1/4" nut driver and set them a
366. Carefully pull out the elbow. It will have the smoker orifi ce attached to it. Remove the orifi ce using a 7/16" open end wrench and replace
371. Follow the safety precautions and steps for main burner removal in the CHANGING THE MAIN BURNER ORIFICES section (steps 1-4).2. Adjust the air s
38To remove the control panel:1. Turn the control knobs to the OFF position and turn off the gas supply to the grill. 2. Turn off the master swit
39TROUBLESHOOTINGIf you have trouble with this Fire Magic® grill, please use this list to identify the problem. By trying one or more of the solutions
4REPLACEMENT PARTS LISTTo order replacement parts, contact your local Fire Magic® dealer.Items in light gray are not available on all models.Some item
40Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Quality Check Date:_________________Burner Orifi ces Nat. L.P. Leak
5REPLACEMENT PARTS LIST (Cont.)REV 5 - 1412081445L-C2-329E660i E790i E1060iItem Description Part No. Qty. Part No. Qty. Part No. Qty.1.St
6REPLACEMENT PARTS LIST (Cont.)REV 5 - 1412081445L-C2-329E660i E790i E1060iItem Description Part No. Qty. Part No. Qty. Part No. Qty.29.D
7COUNTERTOP OVERHANGThe control panel is designed to sit fl ush against the enclosure front wall. If the non-combustible enclosure countertop extends b
8Model Height Width Depth(Top to bottom) (Left to right) (Front to back)Upper hanger to top(with oven)Hanger to hanger(G)Control panelwidth(H)Maximum
9MODEL SPECIFICATIONS (cont.)Note: In addition, a wire diagram specifi c to your unit can be found affi xed to the inside of the control panel.BUILT-IN
Kommentare zu diesen Handbüchern