R.H. Peterson G18-24/30 Series Bedienungshandbuch

1OWNER’S MANUALROBERT H. PETERSON CO. • 14724 East Proctor Avenue, City of Industry, CA 91746ImportantRead these instructions carefully and completely

10OPERATIONAL SAFETY INFORMATIONOPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLYA. SOLID FUEL MUST NOT BE BURNED in a fi replace where this

11OPERATIONAL SAFETY INFORMATION (Cont.)OPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLYN. This appliance is intended for supplemental heati

1212EVENING FYRE LOGS - PARTS LISTFront viewTop view EFV-24 24" EVENING FYRE LOG SETITEM PART DESCRIPTION NO. NO. 1. EFVL-20BR-1 Bo

13EVENING SPLIT LOGS - PARTS LISTFront viewTop view24" LOG SET ESV-24 24" EVENING FYRE SPLIT LOG SETITEM PART DESCRIPTION NO. NO.

1412EVENING FYRE CHARRED LOGS - PARTS LIST ECV-24 24" EVENING FYRE CHARRED LOG SETITEM PART DESCRIPTION NO. NO. 1. ECVL-20BR Bottom

15BURNER PARTSG18-24/30-15(M)(P) ITEM DESCRIPTION NO. 1. Grate assembly 2. Valve assembly (natural) Valve assembly (L.P.) 3. Piezo ignitor

16BURNER PARTS LIST FOR MANUAL VALVE ITEM DESCRIPTION NO. 1. Grate assembly 2. Valve assembly (natural) or Valve assembly (L.P.) 3. Ember burn

17BURNER PARTS (Cont.) ITEM DESCRIPTION NO. 1. Grate assembly 2. Valve assembly (natural) Valve assembly (L.P.) 3. Ember burner 4. ODS pilo

18BURNER PARTS (Cont.) ITEM DESCRIPTION NO. 1. Grate assembly 2. 01 series electronic valve assembly with built in receiver 3. Main burne

19This appliance is for installation in a solid-fuel-burning fi replace (masonry fi replace or manufactured fi replace) with a working fl ue and construct

2TABLE OF CONTENTSL-F2-090REV 10 - 14052813003 SPECIFICATIONS AND REQUIREMENTS4 IMPORTANT SAFETY INFORMATION5 VENTILATION AND CONFINED SPACE SAFETY

20INSTALLATION IMPORTANTFor all valves, the air MUST be purged from the gas line before the ODS pilot will light properly. The time taken to do this w

21NATURAL GASMANUAL PRESSURE MILLIVOLT PRESSURERegulator pressure reading: 3.5" w.c. Outlet pressure reading:(Flame adjustment on high)3.5"

22INSTALLATION (Cont.)GLOWING EMBER PLACEMENTThe Glowing Embers are supplied in a single bag (Fig. 22-1). It is important that the embers be used in t

23WOOD CHIP PLACEMENTThe decorative wood chips provided with the log set are for aesthetics only and do not affect operation of the G18 series unvente

24EVENING FYRE SPLIT LOG PLACEMENTLog placement is critical to ensure stability of the logs and proper performance of the Real-Fyre® gas log set. Be s

25INSTALLATION (Cont.)CLEANING AND SERVICING SAFETY INFORMATIONDAMPER CLAMP INSTRUCTIONS (IF APPLICABLE)The damper clamp with hex bolt (Fig. 25-1) is

26Only limited cleaning will be required under normal use of the unvented gas log set.TO CLEAN THE LOG SET 1. Remove the log set and embers. Use a va

27Observe the fl ames. The main burner fl ames should be blue at the base and a combination of blue/yellow at the body and at the tips. They should be 5

28NOTES PAGEPlease use this page to record any information that you may want to have at hand.

WARNINGIf you do not follow these instructions exactly, a fi re or explosion may result, causing property damage, personal injury, or loss of life.LIGH

3SPECIFICATIONS AND REQUIREMENTSWARNING: This appliance is for installation only in a:1. Solid-fuel-burning masonry or UL-127 factory-built fi replac

30WARNING: If you do not follow these instructions exactly, a fi re or explosion may result, causing property damage, personal injury, or loss of life

311. Locate your Series 12 control valve (p. 15). Turn the control knob (Fig. 31-4) from the OFF position (see Fig. 31-1) slightly counterclockwise

32WARNING: If you do not follow these instructions exactly, a fi re or explosion may result, causing property damage, personal injury, or loss of life

33TROUBLESHOOTINGBURNER SHUTTING DOWN DURING OPERATIONPOSSIBLE CAUSE SOLUTIONSA. Insufficient or excessive gas pressureA1. Check gas pressure (Read G

34TROUBLESHOOTING (Cont.)HIGH CO - CARBON MONOXIDE DETECTORS IN HOME TURNING ALARM ONA. High CO levels A. TURN OFF UNIT IMMEDIATELY.B. Call a quali

35TROUBLESHOOTING (Cont.)POSSIBLE CAUSE SOLUTIONSA. Low gas pressure A. Check gas pressure (see Section 1, A1 of this table).B. Drafts in room B.

36Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Quality Check Date:_________________Burner Orifi ces Nat. L.P. Leak

4UNVENTED ROOM HEATER GENERAL SAFETY INFORMATIONA. WARNING: CARBON MONOXIDE POISONING MAY LEAD TO DEATH.When used without fresh air, gas appliances m

5Your vent-free gas burner system SHALL NOT BE INSTALLED IN A CONFINED SPACE or unusually tight construction unless provisions are made for adequate c

6MINIMUM CLEARANCES TO COMBUSTIBLES If the vent-free burner system is installed in a factory built fi replace, follow the manufacturer’s guidelines for

7MINIMUM CLEARANCES TO COMBUSTIBLES (Cont.)IF YOU CANNOT MEET THESE MINIMUM CLEARANCES, YOU MUST OPERATE THE VENT-FREE GAS BURNER SYSTEM WITH THE CHIM

8WARNINGTHIS APPLIANCE IS EQUIPPED FOR EITHER NATURAL OR PROPANE GAS.FIELD CONVERSION IS NOT PERMITTED.PRE-INSTALLATION AND FIREPLACE PREPARATION SAFE

9INSTALLATION SAFETY INFORMATIONINSTALLATION SAFETY GUIDELINESA. Carefully inspect the burner and log cartons for shipping damage. If any parts are m